Satec PM175 Manual User Manual Page 107
- Page / 168
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Chapter 4 PAS Application Software
Configuring Communication Protocols
Series PM175 Powermeters
107
Option
Range
Default
Description
Rapid Voltage Changes
Repetition Rate
1-10
1
Defines the maximum repetition rate in variations
per hour (equal or less than) for rapid voltage
changes. Voltage changes at higher rates are not
classified since they will be subject for flicker.
Flicker
Pst Period
1-10 min
10 min
Defines the period of time for the short-term
flicker evaluation. The standard setting of 10
minutes can be temporarily changed in the device
for testing purposes.
Harmonic Voltage
THD, up to
order
25-50
40
Defines the highest harmonic order included in
the THD evaluation.
Harmonics, up
to order
25-50
25
Defines the highest harmonic order for evaluation
of the harmonic voltages.
Interharmonic Voltage
Evaluation
Disabled,
Enabled
Disabled
Enables the evaluation of the interharmonic
voltages
THD, up to
order
25-50
40
Defines the highest interharmonic order included
in the THD evaluation.
Interharmonics,
up to order
25-50
25
Defines the highest harmonic order for evaluation
of the interharmonic voltages.
Mains Signaling Voltage
Evaluation
Disabled,
Enabled
Disabled
Enables the evaluation of the mains signaling
voltages
1st Signaling
Frequency
110-3000
Hz
183.0 Hz
Specifies the mains signaling frequency for the
compliance evaluation
2nd Signaling
Frequency
110-3000
Hz
191.0 Hz
Specifies the mains signaling frequency for the
compliance evaluation
3rd Signaling
Frequency
110-3000
Hz
217.0 Hz
Specifies the mains signaling frequency for the
compliance evaluation
4th Signaling
Frequency
110-3000
Hz
317.0 Hz
Specifies the mains signaling frequency for the
compliance evaluation
Clearing EN50160 Evaluation Counters
To clear the present contents of the EN50160 evaluation
counters before starting your EN50160 evaluation, check the
On-line button, select Reset from the Monitor menu, and then
Click on the “Clear EN50160 Counters” button (for more
information, see Resetting Accumulators and Clearing Log
Files).
Configuring Communication Protocols
This section describes how to customize protocol options for
use with your application software.
Configuring Modbus
Modbus Point Mapping
The PM175 provides 120 user assignable registers in the
address range of 0 to 119. You can re-map any register
available in the meter to any assignable register so that
Modbus registers that reside at different locations may be
simply accessed using a single request by re-mapping them to
adjacent addresses.
- Powermeter and Power 1
- Quality Analyzer 1
- LIMITED WARRANTY 2
- WARNING 2
- Table of Contents 3
- Features: 6
- Measured Parameters 8
- Chapter 2 Installation 10
- Chapter 2 Installation 11
- Mechanical Installation 11
- DIN Rail Mounting 13
- Remote Display Installation 14
- Special Cutout 15
- Electrical Connection 16
- Electrical Installation 18
- Terminals 19
- Power Source Connection 19
- Chassis Ground Connection 19
- Wiring Diagrams 20
- I/O Connections 25
- Analog Outputs 26
- Analog Inputs 26
- Communications Connections 27
- COM1 RS-422/485 Connection 28
- COM1 Ethernet Connection 29
- RS-485 MULTI-DROP CONNECTION 31
- Indicators and Controls 32
- Data Display 33
- Navigation Buttons 34
- Common Measurements Display 35
- Energy Display 38
- Status Display 39
- Using the Menus 41
- Entering the Password 42
- Selecting a Menu Entry 42
- THD/TDD 43
- Menu Operations 44
- Device Options 45
- Network Address 47
- Counters Setup 47
- Control Setpoint Setup 48
- Analog Inputs Setup 49
- Analog Outputs Setup 51
- Analog Expander Setup 52
- Timers Setup 53
- Display Setup 53
- Meter Security 54
- Setting the Device Clock 55
- Demands 56
- Configuration Database 57
- Setting up Communications 57
- Configuring a Modem 59
- Setting Up the Meter 60
- Authorization 61
- Setting Up the Ethernet 62
- General Meter Setup 63
- Basic Meter Setup 64
- Local Settings 67
- Using Digital Inputs 68
- Using Relay Outputs 69
- Programming Analog Inputs 71
- Programming Analog Outputs 73
- Using Counters 76
- Using Periodic Timers 77
- Using Control Setpoints 77
- Recording Setpoint Events 81
- Registers 82
- Configuring Recorders 86
- Conventional Data Log Files 88
- EN50160 Background 94
- Evaluation Techniques 95
- Methods of Evaluation 97
- Voltage Interruptions 99
- Temporary Overvoltages 99
- Series PM175 Powermeters 100
- Harmonic Voltage 101
- Interharmonic Voltage 101
- EN50160 PQ Recorder Setup 103
- EN50160 Advanced Setup 106
- Configuring Modbus 107
- Configuring DNP3 108
- Configuring DNP Class 0 110
- Remote Device Control 113
- Event Flags 114
- Device Diagnostics 114
- Updating the Clock 115
- Administration 117
- Upgrading Device Firmware 117
- Monitoring Devices 119
- Retrieving Log Files 120
- Viewing Recorded Files 122
- Event Log 123
- Filtering Events 124
- Customizing Reports 128
- Viewing the Data Log 129
- Viewing Waveforms 130
- Manual Converting 138
- Automatic Converting 139
- Environmental Conditions 140
- Construction 140
- Power Supply 140
- Input Ratings 140
- Relay Outputs 141
- Digital Inputs 141
- Optional Analog Inputs 141
- Optional Analog Outputs 141
- Communication Ports 142
- Real-time Clock 142
- Log Memory 142
- Display Module 142
- Standards Compliance 143
- Measurement Specifications 144
- Setpoint Triggers 146
- Setpoint Actions 148
- Data Logging 150
- Appendix F Data Scales 167
Related products and manuals for Equipment Satec PM175 Manual
Equipment Satec RGM180 User Manual
(24 pages)
(24 pages)
Equipment Satec PM296 User Manual
(77 pages)
(77 pages)
Equipment Satec RSC232 User Manual
(10 pages)
(10 pages)
Equipment Satec 1771DB User Manual
(17 pages)
(17 pages)
Equipment Satec SLC500 User Manual
(24 pages)
(24 pages)
© 2020, manymanuals.com. All rights reserved. | 0.252 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals