Satec PM175 Manual User Manual Page 78
- Page / 168
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Chapter 4 PAS Application Software
General Meter Setup
78
Series PM175 Powermeters
user to define a logical expression based on measured analog
and digital values that produce a required action.
The meter provides 16 control setpoints with programmable
operate and release delays. Each setpoint evaluates a logical
expression with up to four arguments using OR/AND logic.
Whenever an expression is evaluated as “true”, the setpoint
performs up to four concurrent actions that can send a
command to the output relays, increment or decrement a
counter, or trigger a recorder.
The logical controller provides very fast response to events.
The scan time for all setpoints is 1/2 cycle time (8.8 ms at
60Hz and 10 ms at 50 Hz).
To program the setpoints, select General Setup from the Meter
Setup menu, and then click on the Control/Alarm Setpoints
tab.
The available setpoint options are described in the following
table.
Option
Range
Description
Triggers
OR/AND
OR, AND
The logical operator for the trigger
Trigger
parameter
See Appendix C
The trigger parameter that is used as an argument in
the logical expression
Operate limit
The threshold (in primary units) at which the
conditional expression would be evaluated to true.
Not applicable for digital triggers.
Release limit
The threshold (in primary units) at which the
conditional expression would be evaluated to false.
Defines the hysteresis for analog triggers. Not
applicable for digital triggers.
Actions
Action
See Appendix C
The action performed when the setpoint expression is
evaluated to true (the setpoint is in operated state)
- Powermeter and Power 1
- Quality Analyzer 1
- LIMITED WARRANTY 2
- WARNING 2
- Table of Contents 3
- Features: 6
- Measured Parameters 8
- Chapter 2 Installation 10
- Chapter 2 Installation 11
- Mechanical Installation 11
- DIN Rail Mounting 13
- Remote Display Installation 14
- Special Cutout 15
- Electrical Connection 16
- Electrical Installation 18
- Terminals 19
- Power Source Connection 19
- Chassis Ground Connection 19
- Wiring Diagrams 20
- I/O Connections 25
- Analog Outputs 26
- Analog Inputs 26
- Communications Connections 27
- COM1 RS-422/485 Connection 28
- COM1 Ethernet Connection 29
- RS-485 MULTI-DROP CONNECTION 31
- Indicators and Controls 32
- Data Display 33
- Navigation Buttons 34
- Common Measurements Display 35
- Energy Display 38
- Status Display 39
- Using the Menus 41
- Entering the Password 42
- Selecting a Menu Entry 42
- THD/TDD 43
- Menu Operations 44
- Device Options 45
- Network Address 47
- Counters Setup 47
- Control Setpoint Setup 48
- Analog Inputs Setup 49
- Analog Outputs Setup 51
- Analog Expander Setup 52
- Timers Setup 53
- Display Setup 53
- Meter Security 54
- Setting the Device Clock 55
- Demands 56
- Configuration Database 57
- Setting up Communications 57
- Configuring a Modem 59
- Setting Up the Meter 60
- Authorization 61
- Setting Up the Ethernet 62
- General Meter Setup 63
- Basic Meter Setup 64
- Local Settings 67
- Using Digital Inputs 68
- Using Relay Outputs 69
- Programming Analog Inputs 71
- Programming Analog Outputs 73
- Using Counters 76
- Using Periodic Timers 77
- Using Control Setpoints 77
- Recording Setpoint Events 81
- Registers 82
- Configuring Recorders 86
- Conventional Data Log Files 88
- EN50160 Background 94
- Evaluation Techniques 95
- Methods of Evaluation 97
- Voltage Interruptions 99
- Temporary Overvoltages 99
- Series PM175 Powermeters 100
- Harmonic Voltage 101
- Interharmonic Voltage 101
- EN50160 PQ Recorder Setup 103
- EN50160 Advanced Setup 106
- Configuring Modbus 107
- Configuring DNP3 108
- Configuring DNP Class 0 110
- Remote Device Control 113
- Event Flags 114
- Device Diagnostics 114
- Updating the Clock 115
- Administration 117
- Upgrading Device Firmware 117
- Monitoring Devices 119
- Retrieving Log Files 120
- Viewing Recorded Files 122
- Event Log 123
- Filtering Events 124
- Customizing Reports 128
- Viewing the Data Log 129
- Viewing Waveforms 130
- Manual Converting 138
- Automatic Converting 139
- Environmental Conditions 140
- Construction 140
- Power Supply 140
- Input Ratings 140
- Relay Outputs 141
- Digital Inputs 141
- Optional Analog Inputs 141
- Optional Analog Outputs 141
- Communication Ports 142
- Real-time Clock 142
- Log Memory 142
- Display Module 142
- Standards Compliance 143
- Measurement Specifications 144
- Setpoint Triggers 146
- Setpoint Actions 148
- Data Logging 150
- Appendix F Data Scales 167
Related products and manuals for Equipment Satec PM175 Manual
Equipment Satec RGM180 User Manual
(24 pages)
(24 pages)
Equipment Satec PM296 User Manual
(77 pages)
(77 pages)
Equipment Satec RSC232 User Manual
(10 pages)
(10 pages)
Equipment Satec 1771DB User Manual
(17 pages)
(17 pages)
Equipment Satec SLC500 User Manual
(24 pages)
(24 pages)
© 2020, manymanuals.com. All rights reserved. | 1.297 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals