Satec PM175 Manual User Manual Page 34
- Page / 168
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Chapter 3 Display Operations
Data Display
34
Series PM175 Powermeters
Primary and Secondary Volts
Volts can be displayed in primary (default) or secondary units.
The volts display mode can be changed through the Display
Setup menu.
Phase Power Readings
In configurations with the neutral wire, in addition to total
three-phase powers, the meter can show per-phase power
readings. By default, they are disabled. See Display Setup on
how to enable per-phase power readings in your meter.
Fundamental Component
The meter can display total power factor and active power for
the fundamental component if it is enabled through the Display
Setup menu. Whenever phase power readings are allowed,
the PM175 also displays per-phase power factor and active
power for the fundamental component.
Auto Return
If no buttons are pressed for 30 seconds while the display
Auto Return option is enabled, the display automatically
returns to the main screen from any other measurement
display or programming mode.
The Auto Return option can be enabled through the Display
Setup menu
Auto Scroll
If no buttons are pressed for 30 seconds while in the common
measurements display, and the Auto Scroll option is enabled
in the meter, the display automatically scrolls through all
available pages. The scroll interval can be adjusted through
the Display Setup menu.
To stop auto scrolling, press briefly the UP or DOWN button.
Navigation Buttons
In Data Display mode, the navigation buttons function as
follows.
The MIN/MAX button switches to the Min/Max - Maximum
Demands display pages. When briefly pressed again, it
switches back to the common measurements display.
The PQ button switches between different power
quality/harmonic displays: Total Harmonics, Individual Voltage
and Current Harmonics, and Power Quality parameters –
short-term (Pst) and long-term (Plt) flicker, and voltage and
current negative sequence unbalance. When briefly pressed
once again, it switches back to the common measurements
display
The UP and DOWN arrow buttons, labeled by arrowheads,
scroll forwards and backwards through the display pages.
Pressed briefly, they move one page forward or backward. If
you hold down the button the display pages are scrolled at rate
of a twice per second.
ENERGY
ENTER
PQ
ESC
MIN
MAX
SELECT
- Powermeter and Power 1
- Quality Analyzer 1
- LIMITED WARRANTY 2
- WARNING 2
- Table of Contents 3
- Features: 6
- Measured Parameters 8
- Chapter 2 Installation 10
- Chapter 2 Installation 11
- Mechanical Installation 11
- DIN Rail Mounting 13
- Remote Display Installation 14
- Special Cutout 15
- Electrical Connection 16
- Electrical Installation 18
- Terminals 19
- Power Source Connection 19
- Chassis Ground Connection 19
- Wiring Diagrams 20
- I/O Connections 25
- Analog Outputs 26
- Analog Inputs 26
- Communications Connections 27
- COM1 RS-422/485 Connection 28
- COM1 Ethernet Connection 29
- RS-485 MULTI-DROP CONNECTION 31
- Indicators and Controls 32
- Data Display 33
- Navigation Buttons 34
- Common Measurements Display 35
- Energy Display 38
- Status Display 39
- Using the Menus 41
- Entering the Password 42
- Selecting a Menu Entry 42
- THD/TDD 43
- Menu Operations 44
- Device Options 45
- Network Address 47
- Counters Setup 47
- Control Setpoint Setup 48
- Analog Inputs Setup 49
- Analog Outputs Setup 51
- Analog Expander Setup 52
- Timers Setup 53
- Display Setup 53
- Meter Security 54
- Setting the Device Clock 55
- Demands 56
- Configuration Database 57
- Setting up Communications 57
- Configuring a Modem 59
- Setting Up the Meter 60
- Authorization 61
- Setting Up the Ethernet 62
- General Meter Setup 63
- Basic Meter Setup 64
- Local Settings 67
- Using Digital Inputs 68
- Using Relay Outputs 69
- Programming Analog Inputs 71
- Programming Analog Outputs 73
- Using Counters 76
- Using Periodic Timers 77
- Using Control Setpoints 77
- Recording Setpoint Events 81
- Registers 82
- Configuring Recorders 86
- Conventional Data Log Files 88
- EN50160 Background 94
- Evaluation Techniques 95
- Methods of Evaluation 97
- Voltage Interruptions 99
- Temporary Overvoltages 99
- Series PM175 Powermeters 100
- Harmonic Voltage 101
- Interharmonic Voltage 101
- EN50160 PQ Recorder Setup 103
- EN50160 Advanced Setup 106
- Configuring Modbus 107
- Configuring DNP3 108
- Configuring DNP Class 0 110
- Remote Device Control 113
- Event Flags 114
- Device Diagnostics 114
- Updating the Clock 115
- Administration 117
- Upgrading Device Firmware 117
- Monitoring Devices 119
- Retrieving Log Files 120
- Viewing Recorded Files 122
- Event Log 123
- Filtering Events 124
- Customizing Reports 128
- Viewing the Data Log 129
- Viewing Waveforms 130
- Manual Converting 138
- Automatic Converting 139
- Environmental Conditions 140
- Construction 140
- Power Supply 140
- Input Ratings 140
- Relay Outputs 141
- Digital Inputs 141
- Optional Analog Inputs 141
- Optional Analog Outputs 141
- Communication Ports 142
- Real-time Clock 142
- Log Memory 142
- Display Module 142
- Standards Compliance 143
- Measurement Specifications 144
- Setpoint Triggers 146
- Setpoint Actions 148
- Data Logging 150
- Appendix F Data Scales 167
Related products and manuals for Equipment Satec PM175 Manual
Equipment Satec RGM180 User Manual
(24 pages)
(24 pages)
Equipment Satec PM296 User Manual
(77 pages)
(77 pages)
Equipment Satec RSC232 User Manual
(10 pages)
(10 pages)
Equipment Satec 1771DB User Manual
(17 pages)
(17 pages)
Equipment Satec SLC500 User Manual
(24 pages)
(24 pages)
© 2020, manymanuals.com. All rights reserved. | 0.348 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals