Satec PM175 Manual User Manual Page 36
- Page / 168
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Chapter 3 Display Operations
Data Display
36
Series PM175 Powermeters
Common Measurements (Main Display)
6
Ph.L1
PF
kW/MW
Phase L1 powers
(if enabled)
7
kVA/MVA
Ph.L1
kvar/Mvar
Phase L1 powers
(if enabled)
8
Ph.L2
PF
kW/MW
Phase L2 powers
(if enabled)
9
kVA/MVA
Ph.L2
kvar/Mvar
Phase L2 powers
(if enabled)
10
Ph.L3
PF
kW/MW
Phase L3 powers
(if enabled)
11
kVA/MVA
Ph.L3
kvar/Mvar
Phase L3 powers
(if enabled)
12
H01
PF
kW/MW
Fundamental total powers
(if enabled)
13
H1.L1
PF
kW/MW
Fundamental phase L1 powers
(if enabled)
14
H1.L2
PF
kW/MW
Fundamental phase L2 powers
(if enabled)
15
H1.L3
PF
kW/MW
Fundamental phase L3 powers
(if enabled)
16
An.In
AI1
AI2
Analog inputs (optional)
Min/Max and Max. Demands Display
Press the MIN/MAX button. The MIN/MAX LED, or MAX
DEMAND LED in the PM175, is illuminated when in the
MIN/MAX display. Use the UP and DOWN arrow buttons to
scroll through the Min/Max and Max. Demand pages.
Note that volts readings are line-to-neutral in 4LN3, 3LN3 and
3BLN3 wiring modes, and line-to-line in other modes.
Min/Max and Maximum Demands
1
Lo
V1/V12
V2/V23
V3/V31
Minimum volts
2
Lo
I1
I2
I3
Minimum amps
3
Lo
kVA/MVA
PF
kW/MW
Minimum total VA
Minimum total PF (absolute)
Minimum total W
4
Lo
In
Hz
kvar/Mvar
Minimum neutral current
Minimum frequency
Minimum total var
5
Hi
V1/V12
V2/V23
V3/V31
Maximum volts
6
Hi
I1
I2
I3
Maximum amps
7
Hi
kVA/MVA
PF
kW/MW
Maximum total VA
Maximum total PF (absolute)
Maximum total W
MIN
MAX
- Powermeter and Power 1
- Quality Analyzer 1
- LIMITED WARRANTY 2
- WARNING 2
- Table of Contents 3
- Features: 6
- Measured Parameters 8
- Chapter 2 Installation 10
- Chapter 2 Installation 11
- Mechanical Installation 11
- DIN Rail Mounting 13
- Remote Display Installation 14
- Special Cutout 15
- Electrical Connection 16
- Electrical Installation 18
- Terminals 19
- Power Source Connection 19
- Chassis Ground Connection 19
- Wiring Diagrams 20
- I/O Connections 25
- Analog Outputs 26
- Analog Inputs 26
- Communications Connections 27
- COM1 RS-422/485 Connection 28
- COM1 Ethernet Connection 29
- RS-485 MULTI-DROP CONNECTION 31
- Indicators and Controls 32
- Data Display 33
- Navigation Buttons 34
- Common Measurements Display 35
- Energy Display 38
- Status Display 39
- Using the Menus 41
- Entering the Password 42
- Selecting a Menu Entry 42
- THD/TDD 43
- Menu Operations 44
- Device Options 45
- Network Address 47
- Counters Setup 47
- Control Setpoint Setup 48
- Analog Inputs Setup 49
- Analog Outputs Setup 51
- Analog Expander Setup 52
- Timers Setup 53
- Display Setup 53
- Meter Security 54
- Setting the Device Clock 55
- Demands 56
- Configuration Database 57
- Setting up Communications 57
- Configuring a Modem 59
- Setting Up the Meter 60
- Authorization 61
- Setting Up the Ethernet 62
- General Meter Setup 63
- Basic Meter Setup 64
- Local Settings 67
- Using Digital Inputs 68
- Using Relay Outputs 69
- Programming Analog Inputs 71
- Programming Analog Outputs 73
- Using Counters 76
- Using Periodic Timers 77
- Using Control Setpoints 77
- Recording Setpoint Events 81
- Registers 82
- Configuring Recorders 86
- Conventional Data Log Files 88
- EN50160 Background 94
- Evaluation Techniques 95
- Methods of Evaluation 97
- Voltage Interruptions 99
- Temporary Overvoltages 99
- Series PM175 Powermeters 100
- Harmonic Voltage 101
- Interharmonic Voltage 101
- EN50160 PQ Recorder Setup 103
- EN50160 Advanced Setup 106
- Configuring Modbus 107
- Configuring DNP3 108
- Configuring DNP Class 0 110
- Remote Device Control 113
- Event Flags 114
- Device Diagnostics 114
- Updating the Clock 115
- Administration 117
- Upgrading Device Firmware 117
- Monitoring Devices 119
- Retrieving Log Files 120
- Viewing Recorded Files 122
- Event Log 123
- Filtering Events 124
- Customizing Reports 128
- Viewing the Data Log 129
- Viewing Waveforms 130
- Manual Converting 138
- Automatic Converting 139
- Environmental Conditions 140
- Construction 140
- Power Supply 140
- Input Ratings 140
- Relay Outputs 141
- Digital Inputs 141
- Optional Analog Inputs 141
- Optional Analog Outputs 141
- Communication Ports 142
- Real-time Clock 142
- Log Memory 142
- Display Module 142
- Standards Compliance 143
- Measurement Specifications 144
- Setpoint Triggers 146
- Setpoint Actions 148
- Data Logging 150
- Appendix F Data Scales 167
Related products and manuals for Equipment Satec PM175 Manual
Equipment Satec RGM180 User Manual
(24 pages)
(24 pages)
Equipment Satec PM296 User Manual
(77 pages)
(77 pages)
Equipment Satec RSC232 User Manual
(10 pages)
(10 pages)
Equipment Satec 1771DB User Manual
(17 pages)
(17 pages)
Equipment Satec SLC500 User Manual
(24 pages)
(24 pages)
© 2020, manymanuals.com. All rights reserved. | 0.292 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals